Home >> Products >> Spill Containment >> Spill Containment Berms and Walls >> Berm Builder – Around Machinery or Equipment

Berm Builder – Around Machinery or Equipment

SafeRack, UltraTech

Build a barrier around machinery or equipment that is permanently mounted or cannot easily be moved

Most of our spill containment products are designed to be put in place and then have the potential offending “spillers” placed in or on the containment unit. But large, heavy, or previously secured/bolted down equipment or machinery can make that very difficult or impossible.

The Ultra-Berm Builder solves that problem. This component system can be built to just about any size and/or shape that might be needed for your spill containment application.

View Full Text

Question, Get a Quote, Live Demo or Request an On-Site Visit

Our experts simplify the complex

Order Now

Request On-Site Visit

SafeRack, UltraTech

Build a barrier around machinery or equipment that is permanently mounted or cannot easily be moved

The Ultra-Berm Builder solves that problem. This component system can be built to just about any size and/or shape that might be needed for your spill containment application.

View Full Text

Key Features:

The component system provides flexibility to create a semi-permanent, high-visibility custom barrier.
Durable, vinyl covering resists oils, coolants, and most chemicals.
Cut to length and secure to floor with included sealant, then seal seams with the vinyl adhesive.
Economical containment for leaks and spills around machinery and equipment – no need to build expensive cement or angle iron curbs.
High-visibility yellow color draws attention to the barrier for increased safety.
Easy removal requires only a flat-bladed shovel.

Kit Contents (p/n 8640):

(2) 25’ Ultra-Berm Builder Walls
(4) Ultra-Berm Builder Corners
(6) Floor Sealant Tubes
(1) 10 foot section Connector Collar
(1) 8oz. Industrial Vinyl Adhesive

Part #	Description	Dimensions	Qty	Weight lbs. (kg)	Data Sheet
8640	Full Kit	50’ x 5½” x 2” (15.2 m x 140 mm x 51 mm)	1/box	21.0 (9.5)	Download
8641	Straight Section	15’ x 5½” x 2” (4.6 m x 140 mm x 51 mm)	1/box	6.0 (3.0)	Download
8642	Corner	7¼” x 5½” x 2” (184 mm x 140 mm x 51 mm)	2/box	2.0 (1.0)	Download
8643	Connecting Collar	10’ x 4” (3m x 102mm)	1/box	1.0 (0.5)	Download
8644	Floor Sealant (10.3 fl. oz. tube)		6/box	8.0 (3.5)
8645	Vinyl Adhesive (8 oz. can)		1/box	1.0 (0.5)

Ultra-Berm Builder Installation Information

The floor must be clean of debris. Any build-up of grease and oil must be removed. Failure to do so may result in premature failure of The Ultra-Berm Builder® sealant.
To apply The Ultra-Berm Builder® over frost cracks and form separations, fi rst fi ll these areas with caulking.
Apply 2 continuous beads of caulking on the bottom of the The Ultra-Berm Builder® approximately 1” in from its side and ends, along its entire length.
Place The Ultra-Berm Builder® and apply pressure to its entire length to seal it to the floor. Note: To ensure proper sealing on uneven surfaces, you may need to apply extra sealant and also more direct pressure .
To add sections or attach corners to the The Ultra-Berm Builder® , apply vinyl adhesive to the built-in vinyl cover and the end of the berm. Then mold the vinyl cover over the berm end and hold in place (approximately 30 seconds).

IMPORTANT NOTES:

If it has been stored coiled, let the Ultra-Berm Builder® lie fl at for 2 hours before installing it.
Let the Ultra-Berm Builder® cure (sealant and glue) for at least one hour before use.
To cut the Ultra-Berm Builder®, use a utility knife along with a straight edge.
To remove the Ultra-Berm Builder®, scrape with a flat-blade shovel and use silicone remover to clean caulking from base.